-
-
...m(50mil);线与线之间和线与焊盘之间的距离大于等于0.33mm(13mil),实际应用中,条件允许时应考虑加大距离; : 布线密度较高时,可考虑(但不建议)采用IC脚间走两根线,线的宽度为0.254mm(10mil),线间距不小于0.254mm(10mil)。特殊情...
-
-
...xtern uchar fnPR12(uchar uCmd); // 写无参数的指令
extern uchar fnPR13(uchar uData); // 写数据
extern unsigned int Adc0832(unsigned char channel);
extern void Line( unsigned char x1, unsigned char y1, unsigned char x2, unsigned char y2, bit Mode);
extern void Pixel(unsigned char PointX,...
-
-
...总数为多少?1.程序分析: 兔子的规律为数列1,1,2,3,5,8,13,21....2.程序源代码:main(){long f1,f2;int i;f1=f2=1;for(i=1;i〈=20;i++) { printf(“%12ld %12ld“,f1,f2); if(i%2==0) printf(“\n“);/*控制输出,每行四个*/ f1=f1+f2; /*前两个月加起...
-
-
...le 1.3368 1.3343 0.2101 0.5779 0.2130 0.5015 1.3238 1.3569 0.2066 0.4591 &n...
-
-
...x00,0x00,// (10)
0x00,0x00,0x00,0x47,0x00,0x00,0x00,0x00,//!
0x00,0x23,0x13,0x08,0x64,0x62,0x00,0x00,//%
0x00,0x36,0x49,0x55,0x22,0x50,0x00,0x00,//&
0x00,0x14,0x08,0x3e,0x08,0x14,0x00,0x00,//*
0x00,0x08,0x08,0x3e,0x08,0x08,0x00,0x00,//+
0x00,0x08,0x08,0x08,0x08,0x08,0x00,0x00,//-
0x00,0x0...
-
-
....kosrp/ib_srp.koAnother example in case of Ubuntu 14.04# pwd/lib/modules/3.13.0-33-generic/updates/dkms# lscompat.koib_cm.koib_iser.koib_sa.koib_umad.koknem.komlx4_ib.komst_pciconf.kordma_ucm.kords_tcp.koeth_ipoib.koib_core.koib_isert.koib_srp.koib_uverbs.komlx4_core.komlx5_core.komst_pci.kords.kosc...
-
-
...x8A,0xEC,0x48,0x00,
0x02,0x5F,0x20,0x18,0x07,0x00,0x1F,0x49,
0x5F,0x20,0x13,0x0C,0x13,0x20,0x78,0x00,
}; //输出空白区域
uc code BAI[]=
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00...
-
-
...nbsp; //总的角点数据 const int frameNumber = 13; //相机标定时需要采用的图像帧数 co...
-
-
...nbsp;11
//#define LF 12
//#define RT 13
#define AD 14 //+
#define SB 15 //-
#define L_O_V_I() EALLOW; &...
-
-
...... PAGEREF _Toc522634555 \h 121.1.5 条件... PAGEREF _Toc522634556 \h 131.2 OpenDDS实现... PAGEREF _Toc522634557 \h 131.2.1 合规性... PAGEREF _Toc522634558 \h 131.2.1.1 DDS合规性... PAGEREF _Toc522634559 \h 131.2.1.2 DDSI-RTPS 合规性... PAGEREF _Toc522634560 \h 141.2.2 DDS规范...