-
-
.... struct linka { 2. int data; 3. linka* next; 4. }; 5. void reverse(linka*& head) { 6. if(head ==NULL) 7. return; 8. linka *pre, *cur, *ne; 9. pre=head; 10.cur=head->next; 11.while(cur) 12.{ 13. ne = cur->next; 14. cur->next = pre; 15. pre = cur; 16. cur = ne; 17.} 18.head->next = NU...
-
-
...rf/iperf-2.0.5.tar.gz?r=http%3A%2F%2Fsourceforge.net%2Fprojects%2Fiperf%2F&ts=1441315914&use_mirror=skylineservers iperf-2.0.5.tar.gz
...
# tar xzvf iperf-2.0.5.tar.gz
...
# cd iperf-2.0.5
# ./configure
....
# make
...
# make install
......
-
-
...等式构建：扭矩与电枢电流成正比：公式 1：Td(Nm) = Km*IA(Amp) 开发的电机扭矩电压与电枢速度成正比：公式 2：VD(Volt) = WD (rad/sec)* Km  得到电机电压内部电机电压公式 3：VH(Volt) = IH(Amp)*RA(Ohm) + LH(Henry)*di(t)/dt(A/s) + VD(V) 电机电压...
-
-
...;  for i=1:br           if ((C(i,f)==1)&&(k==1))                f=i;                k=2;           end       end    &...
-
-
...；
ADC_CONTR = ADC_CONTR | 0x08; //开始转换
while((ADC_CONTR & 0x10) !=0x10); //等待转换标志置位
i = ADC_RES;
j = ADC_RESL;
i = i << 8;
i = i | j;
ADC_CONTR = ADC_CONTR & ~0x10;   //清零转换标志位
ADC_RES = 0x00;
ADC_RESL = 0x00;
re...
-
-
...) {        countx++;        x = x & (x - 1);    }    return countx;}```+ 6+ 7+ 8+ 0> 解析如下：```cppx = x&(x-1);//求x的二进制表达式有多少个1x = x|(x-1);//求x的二进制表达式有多少个0```从右向左数...
-
-
... int j = i -1;        while (j >= 0 && array[j] > val) {  // array[j] > val            array[j+1] = array[j];            j--; &n...
-
-
...(void)
{
unsigned char KeyTemp,CheckValue,Key = 0x00;
CheckValue = P2&0x32;
if(CheckValue==0x32)
return 0x00;
Delay1ms(10);
KeyTemp = P2&0x32;
if(KeyTemp==CheckValue)
return 0x00;
if(!(CheckValue&0x02))
Key|=0x01;
if(!(CheckValue&0x10))
Key|=0x02;
...
-
-
...始化，为中断做准备
while(1)
{
key();
if(hour == hour_n && min == min_n)    //闹钟到时间，蜂鸣器响
{
P3_2 = !P3_2;
delay(50);
}
}
}
-
-
...               if ($1 > timedaysago && $1 < now) print
        }
'  apollocode.log
这里注意，awk传递参数进去执行linux指令时候要加双引号，这个问题花了我几个小时才调试出来，另外，在...
