-
-
...bsp;//定义通信端口
//晶振12MHz
void delay_18B20(unsigned int i)
{
while(i--);
}
//初始化函数
Init_DS18B20(void)
{
unsigned char x=0;
DQ = 1; //DQ复位
delay_18B20(8); //稍做延时
DQ = 0; &...
-
-
...YTE[0x12]
#define LLCD_DATA_RD PBYTE[0x13]
#define RLCD_CMD_WR PBYTE[0x20]
#define RLCD_CMD_RD PBYTE[0x21]
#define RLCD_DATA_WR PBYTE[0x22]
#define RLCD_DATA_RD PBYTE[0x23]
sbit busy=P0^1;
uchar code hz0[]=
{
0x00, 0x00, 0xf8, 0x88, 0x99, 0xea, 0x8c, 0xf8, 0x88, 0xcc, 0xab, 0x99, 0x88, ...
-
-
...nbsp;0x04,0xFC,0x04,0x04,0x04,0x04,0x00,0x00,
0x04,0x04,0x7E,0x01,0x20,0x20,0x20,0x20,
0x20,0x3F,0x20,0x20,0x20,0x20,0x20,0x00,
};
uc code XI[]=
{
//;西 CCEF7
0x02,0xF2,0x12,0x12,0x12,0xFE,0x12,0x12,
0x12,0xFE,0x12,0x12,0x12,0xF2,0x02,0x00,
&...
-
-
...核 18.安装软件 18.1 安装软件 18.2 可疑软件 19.环境变量 20.性能分析 20.1 磁盘使用 20.1.1 磁盘使用情况 20.1.2 磁盘使用过大 20.2 CPU 20.2.1 CPU情况 20.2.2 占用CPU前五进程 20.2.3 占用CPU较多资源进程 20.3 内存 20.3.1 内存情况 2...
-
-
它将20V dc升压至70V dc。它测量输出电压并减去参考电压。 它们的差值传递给PI控制器，PI控制器计算要从输入端汲取的直流电流。 将该参考电流与实际输入电流进行比较，并将它们的差值传递给磁滞带电流控制器，该控制器为开...
-
-
ds18b20#include<reg51.h>
#define uchar unsigned char
#define uint unsigned int
sbit DQ=P3^7;//ds18b20与单片机连接口
sbit RS=P3^0;
sbit RW=P3^1;
sbit EN=P3^2;
unsigned char code str1[]={"temperature: "};
unsigned char code str2[]={" &...
-
-
...%EffDischarge=100 State=CHARGING".format(
bus_name='675',
rating=20,
kwh_rating=20,
initial_state=20
))
dss.run_command(
"New Storage.{bus_name} Bus1={bus_name} phases=1 kV=2.2 kWRated={rating} kWhRated={kwh_rating} kWhStored={initial_state} %IdlingkW=0 %reserve=0 ...
-
-
...8,0x38,0x00}},
{{0x00,0x04,0x18,0x10,0x11,0x16,0x90,0x50,0x10,0x24,0x22,0x20,0x28,0x10,0x00,0x00},
{0x00,0x04,0x04,0x84,0x04,0x44,0x44,0x78,0x88,0x88,0x88,0x08,0x0C,0x04,0x00,0x00}},
{{0x00,0x00,0x02,0x02,0x02,0x02,0xFF,0x04,0x04,0x04,0x04,0x04,0x00,0x00,0x00,0x00},
{0x00,0x04,0x08,0x10,0x20,0xC...
-
-
数字温度传感器DS18B20应用， 使用protues单片机对温度传感器进行仿真，测试，Protues8.5及以上软件打开仿真#include<reg51.h>
#include<DS18B20.c>
code uchar seven_seg[]={0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90};
uchar cp2;...
-
-
...令语法 18命令动词 18参数 18COMMENTS注释 20多行命令MULTI-LINE COMMANDS 20包含外部文件 20工作流程 20代码范例 22COM 接口介绍 24开始使用 COM 接口 24TEXT接口介绍 25电路接口（ CIRCUIT INTERFAC...
